3-D contouring, milling, drilling, reaming, tapping profiling,
We need 120 parts, You or me do machine program (option).
MCAM x3 geometry file supplied, .IGES, most other types too.
Possible repeat work.
1) Material type
alum. 6061 bar 2.000 x .750 x 16.5" x 10pcs or your option.
2) Is a material quote required or is material supplied?
Supplied or You to procure from any source, cut plates or barstock.
3) Quantity ?
120 parts on 10 bars
4) Drawings should be immediately available or necessary specs. (link supplied)
Full cad support any 3-D CAD file type, no .PDF's
Complete package in a .ZIP file posted on website LINK Here.
http://members.cox.net/bostosh0/This for RFQ.zip
5) Required time frame ?
ASAP or negotiated delivery schedule.
6) RFQ ending time ?
when job is let.
7) Full contact information should be supplied upon first contact by email from both parties,
neither should have to reply to rfq@.com ( We will not )
Brian Ostosh <bostosh@cox.net>
Robert Guthrie <bgsnares@yahoo.com>
8) If you the RFQ poster needs help in some of the technical areas then that should be made know initially.
We need no additional help, just program, run and deliver,
Basic +/- .002-.003 tolerances on hole locations, good threads (roll or cut), Body tolerance +0,-.010
Yes I will and can do conventional (old-school) inspection of first article, full bar, or minimum 3 pcs (short bar)
Overnight mail if necessary.
We will deburr and finish the machining scallop marks on fillets.
Your program scallop height = .001 or less. (Use those new software routines)
Figure a clamping and tabbing scheme, vise set-up ok
Please call for confirmation of tooling plan,
Like-maybe the entire quantity be run on a larger X,Y array and
With a .005-,0100 web part-to-part tab along long sides.
Maybe double-back Scotch and the flat side down.
Use those High-Speed router bits light cuts to part-off.
We can part-off and finish .3125 side hole.
9) Make known any special treatments/finishes not necessarily related to the machining process.
Please do not gouge nor bang-up the 2.000 or .750 raw stock dimensions, these are not critical dimensions but will get a polishing. (This is the "ART" of the "part") These dimensions can be up to .005-.010 under.
In other words, the stock could be fly-cut square-up for those stock dimensions, Please protect finish surfaces.
Thanks for the interest in your bid.
We need 120 parts, You or me do machine program (option).
MCAM x3 geometry file supplied, .IGES, most other types too.
Possible repeat work.
1) Material type
alum. 6061 bar 2.000 x .750 x 16.5" x 10pcs or your option.
2) Is a material quote required or is material supplied?
Supplied or You to procure from any source, cut plates or barstock.
3) Quantity ?
120 parts on 10 bars
4) Drawings should be immediately available or necessary specs. (link supplied)
Full cad support any 3-D CAD file type, no .PDF's
Complete package in a .ZIP file posted on website LINK Here.
http://members.cox.net/bostosh0/This for RFQ.zip
5) Required time frame ?
ASAP or negotiated delivery schedule.
6) RFQ ending time ?
when job is let.
7) Full contact information should be supplied upon first contact by email from both parties,
neither should have to reply to rfq@.com ( We will not )
Brian Ostosh <bostosh@cox.net>
Robert Guthrie <bgsnares@yahoo.com>
8) If you the RFQ poster needs help in some of the technical areas then that should be made know initially.
We need no additional help, just program, run and deliver,
Basic +/- .002-.003 tolerances on hole locations, good threads (roll or cut), Body tolerance +0,-.010
Yes I will and can do conventional (old-school) inspection of first article, full bar, or minimum 3 pcs (short bar)
Overnight mail if necessary.
We will deburr and finish the machining scallop marks on fillets.
Your program scallop height = .001 or less. (Use those new software routines)
Figure a clamping and tabbing scheme, vise set-up ok
Please call for confirmation of tooling plan,
Like-maybe the entire quantity be run on a larger X,Y array and
With a .005-,0100 web part-to-part tab along long sides.
Maybe double-back Scotch and the flat side down.
Use those High-Speed router bits light cuts to part-off.
We can part-off and finish .3125 side hole.
9) Make known any special treatments/finishes not necessarily related to the machining process.
Please do not gouge nor bang-up the 2.000 or .750 raw stock dimensions, these are not critical dimensions but will get a polishing. (This is the "ART" of the "part") These dimensions can be up to .005-.010 under.
In other words, the stock could be fly-cut square-up for those stock dimensions, Please protect finish surfaces.
Thanks for the interest in your bid.