Hello RFQWork.com shops!
We are looking for someone to cut us 15 of the attached 1/4" thick aluminum plates. Overall size is 13.0" x 20.5".
We also require the attached stainless plate. 5" x 8", 1/4" thick. 20 quantity.
Holes diameter tolerances are +0.050/-0.005. Locations are +- 0.010. No special finish required. Sharp edges must be broken and deburred if they exist. Typical laser or waterjet finish is acceptable with no further work required. The aluminum part is highly visible and part of an expensive system. Stained / discolored parts and those with deep scratches or pits are not acceptable. The stainless part goes into a weldment and just needs to be free of sharp edges.
We are looking for a job to setup a long term relationship with. We are located in Winona, MN. Preference will be awarded to regional shops and those with the best communications -- but we are open to any US or Canadian shops.
Parts can be shipped on our UPS account. If you are not setup with UPS shipping we can even e-mail you a PDF of a label that you can print out and tape to the box. Payment can be made with credit card, paypal, or company check. We typically pay our bills on the day or receipt of the invoice. We can even pay in advance if need be.
I believe there is about $25 of aluminum in each of the big plates. Target price is ~ $35. There is about $15 of stainless in the small plates. Target prices is ~ $22. But it has been a while since I've priced water jet cutting, so if going rate has changed then we can deal with it. Please quote the two parts individually.
All bids must be received by 2008-05-09 (Thursday) at 8:00 AM CDT. We will award the job immediately. Parts need to be received by 2008-05-22.
If you have any questions please e-mail jj@aprsworld.com or call me @ 507-454-2727.
Thanks,
-James Jarvis
APRS World, LLC
www.aprsworld.com
We are looking for someone to cut us 15 of the attached 1/4" thick aluminum plates. Overall size is 13.0" x 20.5".
We also require the attached stainless plate. 5" x 8", 1/4" thick. 20 quantity.
Holes diameter tolerances are +0.050/-0.005. Locations are +- 0.010. No special finish required. Sharp edges must be broken and deburred if they exist. Typical laser or waterjet finish is acceptable with no further work required. The aluminum part is highly visible and part of an expensive system. Stained / discolored parts and those with deep scratches or pits are not acceptable. The stainless part goes into a weldment and just needs to be free of sharp edges.
We are looking for a job to setup a long term relationship with. We are located in Winona, MN. Preference will be awarded to regional shops and those with the best communications -- but we are open to any US or Canadian shops.
Parts can be shipped on our UPS account. If you are not setup with UPS shipping we can even e-mail you a PDF of a label that you can print out and tape to the box. Payment can be made with credit card, paypal, or company check. We typically pay our bills on the day or receipt of the invoice. We can even pay in advance if need be.
I believe there is about $25 of aluminum in each of the big plates. Target price is ~ $35. There is about $15 of stainless in the small plates. Target prices is ~ $22. But it has been a while since I've priced water jet cutting, so if going rate has changed then we can deal with it. Please quote the two parts individually.
All bids must be received by 2008-05-09 (Thursday) at 8:00 AM CDT. We will award the job immediately. Parts need to be received by 2008-05-22.
If you have any questions please e-mail jj@aprsworld.com or call me @ 507-454-2727.
Thanks,
-James Jarvis
APRS World, LLC
www.aprsworld.com