[closed] Rfq - 33,000 Pcs 303-ss Bellville Washers (not Punched)

Status
Not open for further replies.

james Griffith

New Member
[ CLOSED - WE'VE FOUND A GOOD MATCH. THANK YOU FOR BIDDING ]

We're seeking a quote for Bellville washers made from 303-SS
15,000 pcs 1/2"
15,000 pcs 5/8"
1,500 - 2,000 pcs 11/16" (range is to make quoting easier based on using up a bar)
1,500 - 2,000 pcs 3/4" (range is to make quoting easier based on using up a bar)

See attached CW Specs.pdf NOTE the perpendicular center wall and outside wall. Also attached is a profile tool as an idea if it helps. Our current shop is unable to add any new volume. We're growing. Pricing for 303 is at $0.30 ea. It's not a big job but it repeats especially in 12L14 using the same tooling

These items are historically run on davenport and Brown & Sharpe #2 depending on bar size. If I've listed this under the wrong category please advise

Please don't hesitate to contact me with any questions. I'd like to make a decision by October 15th

Thank You
James Griffith
jgriffith@pfgp.us
 

Attachments

  • CW specs.pdf
    49 KB · Views: 89
  • Profile Tool .jpg
    Profile Tool .jpg
    210.9 KB · Views: 45
  • 2 CW.jpg
    2 CW.jpg
    192.9 KB · Views: 43
Last edited:

bare

New Member
We're seeking a quote for Bellville washers made from 303-SS
15,000 pcs 1/2"
15,000 pcs 5/8"
1,500 - 2,000 pcs 11/16" (range is to make quoting easier based on using up a bar)
1,500 - 2,000 pcs 3/4" (range is to make quoting easier based on using up a bar)

See attached CW Specs.pdf NOTE the perpendicular center wall and outside wall. Also attached is a profile tool as an idea if it helps. Our current shop is unable to add any new volume. We're growing. Pricing for 303 is at $0.30 ea. It's not a big job but it repeats especially in 12L14 using the same tooling

Please don't hesitate to contact me with any questions. I'd like to make a decision by October 15th

Thank You
James Griffith
jgriffith@pfgp.us
Hello
James

Will are happy to quote send print and contact info sales@baremetalsinc.com
Thanks
Bill
Bare Metals Inc
773-283-2211
 
We're seeking a quote for Bellville washers made from 303-SS
15,000 pcs 1/2"
15,000 pcs 5/8"
1,500 - 2,000 pcs 11/16" (range is to make quoting easier based on using up a bar)
1,500 - 2,000 pcs 3/4" (range is to make quoting easier based on using up a bar)

See attached CW Specs.pdf NOTE the perpendicular center wall and outside wall. Also attached is a profile tool as an idea if it helps. Our current shop is unable to add any new volume. We're growing. Pricing for 303 is at $0.30 ea. It's not a big job but it repeats especially in 12L14 using the same tooling

Please don't hesitate to contact me with any questions. I'd like to make a decision by October 15th

Thank You
James Griffith
jgriffith@pfgp.us

Are you supplying the material?

C² Manufacturing
765-305-2575
Csquaredmfg@gmail.com
 

james Griffith

New Member
We can't supply material. we don't buy enough to get your discounts.

The washer is a concave washer with a constant thickness of .09" <- this must remain within .0025", the rest has a more liberal tolerance of .005"

Outside of the thickness, the differences are the ID and OD and width between those which creates the unique angle. Use the dimensions to generate (or calculate) the angles

This PDF has been used for over 8 years so I am at a loss to what info is needed based on the question. I am more than happy to answer but asking for a better drawing on a washer isn't enough information please.
 
Status
Not open for further replies.
Top