Search results

Please quote machining only, 6 pcs in annealed W1. I'll plan to supply as Ø0.5". Quote material separately if you'd like to supply (McMaster Carr). ±0.3mm from CAD profile, standard finish (125/3.2). Zip contains IGES & STP, or email if you don't want to open that. Thanks

STEP or SAT file available. File contains 2 models, 1 is complete part and 1 is an acceptable option (3/8" stock left as-is on one end). Material is cold-rolled 1045, supplied by me. Finish is 125, tolerance is ±0.010 from CAD geometry. thanks

STEP or SAT file available. File contains 2 models, 1 is complete part and 1 is an acceptable option (3/8" stock left as-is on one end). Material is cold-rolled 1045, supplied by me. Finish is 125, tolerance is ±0.010 from CAD geometry. thanks

I need a qty of 10 stainless steel rings made from 1/8" round stock. OD = 11" +0.030 -0.060 Finish & appearance are not critical but the part must be smooth and free of burrs. Please email or PM for print. thanks

Attachment upload is not working for me. This is a small part, about 3" x 0.8". Has 2x 0.207" holes and 1x 0.355" hole, with 2x 45° bends. Tolerances on hole Ø is ±0.005; general tolerance is ±0.010. Please email me and I will send a print. thank you

Obviously making it out of solid stock would be cheaper and easier. The purpose of the design is to LESSEN mass...

From http://www.efunda.com/processes/heat_treat/matl_modify/stress_relieving.cfm : "Machining induces stresses in parts. The bigger and more complex the part, the more the stresses. These stresses can cause distortions in the part long term. If the parts are clamped in service, then...

2 attached pdfs show a difficult part that I've been trying to make. "Process 1" shows the blank, "Process 2" shows the desired part. I had a few of these blanchard ground. They hit the dimensional tolerances, but not the straightness/flatness. They were flat to 0.003 or 0.004. I imagine...

No, not uncommon. We buy 5/16" and 5/8" mild steel plates all the time. Usually 4' x 8' or 4' x 10'. The 5/16" always comes in as CR or HRP&O. The 5/8" always comes in as HR.

Please quote EDM cutting of 1.401 x 1.401" hole only, from supplied blank. ±0.010" on location of your cutting, relative to features on supplied blank. Qty 1. 1 pdf shows complete part, other pdf shows blank with superimposed EDM path. Dxf file available. thank you

I need a quantity of 20 "TT11.5 Rings". EITHER "TT11.5 Ring A" OR "TT11.5 Ring B" AT YOUR OPTION. Please figure out which one would be cheaper or easier, and quote either A or B. thank you!

Here's the Roll Plate and Arm

The pdfs will be online for a few days; email for drawings after 11/14. These parts are prototypes; perpendicularity tolerance is ±0.03° or 0.005" over 10" - however I will NOT be inspecting them to the print. If the parts are as square as possible (on Arm, Arm Lock, and R/Y Angle), I'll be...

Quote fulfilled, thank you

Please view attached pdfs. I am in need of the "LS" part ASAP. I'm on the E Coast; I would prefer not to work with someone on the W Coast due to shipping expenses. If you have a source for 4140 or similar, please quote material and turning separately. If not, I will provide the material...

I have a 4" x 1.5" x 24" bar of hot-rolled W2 tool steel. I want it sliced into smaller bars that will be straightened and blanchard ground to a final size of 0.188 x 1.5 x 24" If you can grind them to final size, quote that separately. Cut quality, taper, and distortion are not issues...

I have a 4" x 1.5" x 24" bar of hot-rolled W2 tool steel. I want it sliced into smaller bars that will be straightened and blanchard ground to a final size of 0.188 x 1.5 x 24" If you can grind them to final size, quote that separately. Cut quality, taper, and distortion are not issues...

Quote Fulfilled, thank you

Quote Fufilled; thank you all

Attached is a pdf for a tapered steel shaft; 24" long. Qty desired: 1 Date desired: 7/6/09 (not urgent) Material: not critical; you supply. 1018 is fine. I'm also interested in a quote using stainless. Everything about this job is not critical except the length; it cannot exceed...